The author of qtHaskell recommends a simpler approach. In addition to the "slotReject" patch below, simply change lines 308-309 of build.pl as follows:
Original postFinally! I spent the entire weekend on this, but I finally managed to compile qtHaskell on OS X. I spent a lot of that time on the internet googling for the error messages I encountered, to no avail. So, to save some time to the next person who google them, here is what worked for me. The qtHaskell documentation recommends that you use their ./build perl script. That almost works, but not quite. Thankfully, by giving arguments to the scripts, we can run the parts which work, and skip over the parts which don't. Speaking of arguments, one the most annoying errors is the "scattered reloc r_address too large" error message which only occurs at the very end of a very length compilation. I stumbled upon a page recommending to use "--extra-ld-opt=--architecture=x86_64" to fix a similar error message, and since then I have superstitiously stuck the argument everywhere I could, just to be sure. So, let's build qtHaskell, shall we? First of all, qtHaskell is a set of Haskell bindings for Qt, so you need to install Haskell and Qt. I used Qt 4.7.1, qtHaskell 1.1.4, and GHC 7.0.4 (64 bits). Actually I had the 32 bits version of GHC at first, and that let to the aforementioned r_address problems, followed by linking problems afterwards. Better upgrade to 64 bits!
brew uninstall ghc brew install ghc --64bitsWe should now be ready to compile qtHaskell proper. There are actually two parallel hierarchies to be compiled, the C++ implementation and its Haskell FFI interface. Both are very large, because, well, Qt is large. First, the C++ part: no problems here, the build script works just fine for this part.
./build user cpp qmake cmake \ --extra-ld-opt=--architecture=x86_64 ./build user cpp-install \ --extra-ld-opt=--architecture=x86_64 --no-sudoNote that even though the "user" flag was given, the build script will still install the files globally in /usr/local/lib/libqtc_*. Presumably, the flag is only for the Haskell part, for which the steps would ideally be as follows.
./build user haskell configure \ --extra-ld-opt=--architecture=x86_64 ./build user haskell build \ --extra-ld-opt=--architecture=x86_64 ./build user haskell-install \ --extra-ld-opt=--architecture=x86_64 --no-sudoUnfortunately, the middle step fails with the following error message.
unrecognised command: makefile (try --help) runghc Setup.hs makefile: No such file or directoryFear not! This cryptic-looking error message is actually a clue towards the solution. Apparently, "runghc Setup.hs makefile" is the command used for building the Haskell part. Using the help, as recommended in the error message, leads to the following alternative build commands.
runghc Setup.hs configure --user \ --extra-ld-opt=--architecture=x86_64 runghc Setup.hs buildUnfortunately, that doesn't work either, at least not with a recent GHC. There is a problem in the qtHaskell code, which leads to the following error message. If you are familiar with Haskell, you should be able to fix the problem on your own. Alternatively, you could grab Uduki's hsQt fork of qtHaskell, which comes pre-patched. Or you might apply the following patch yourself: Now that the source is patched, the Haskell part should finally compile.
runghc Setup.hs buildIf you run out of memory during this phase, just run the command again. And again. As many times as it takes to compile all the targets. When you get the the very last target, qtHaskell is finally linked... and then, like me, you might get one of those nasty "scattered reloc r_address too large" errors. Did you? If so, you might have skipped the very first step and be stuck with a 32 bits version of GHC. Check using "ghc --info". If you insist on using the 32 bits version, you could try the following variant of the build command, which got me through that step. Still got troubles when linking programs using qtHaskell, though.
runghc Setup.hs configure --user --disable-library-for-ghciNow that the Haskell part is built, we can finally install it! This time, the "user" flag is honored.
./build user haskell-install \ --extra-ld-opt=--architecture=x86_64 --no-sudoLet's test this! The qtHaskell helpfully provides the following Hello World code, just put it in a file with the "hs" extension and build it into an executable using "ghc --make".
|At long last. A button!|